HP Z420 ATX modification

Using proprietary OEM motherboards outside their intended use case is not a new subject. OEM motherboards are typically less expensive than their enthusiast counterparts on the second hand market, and they often incorporate features that the enthusiast offers lack, such as an integrated TPM or additional I/O.

The HP Z420 is a workstation based on the LGA 2011 (Sandy/Ivy Bridge-EP) socket, released in 2012. There are various forum threads around the internet discussing how to operate the motherboard with a third-party power supply and chassis, however I have not found a succinct document that outlines all the steps required to use the motherboard without HP original parts.


The motherboard has an 18+8pin power arrangement. The motherboard is almost entirely 12V powered, with +11VSB being the only other voltage present. The pinout of the 18 pin main power connector is as follows:

HP Z210/Z420/Z620 18 pin motherboard power pinout

The following pins are the only pins required to power the motherboard:

Z420 PinDescriptionATX PSU pin
1, 105V output from the motherboardN/A
2-6, 11Ground3, 5, 7, 15, 17-19, 24
7, 12-1512V input10-11
8/PSON16
17+11VSB inputN/A (step-up from +5VSB)
18-12V input (not required)N/A

It is possible to inexpensively build an adapter out of a 24 pin ATX extension table and a DC buck-boost converter to step +5VSB up to +11VSB. You can also find very inexpensive adapters for sale on eBay or AliExpress which are purpose built for the Z420/Z620:

ATX to Z420/Z620 18pin adapter

These adapters are typically around $5 and include the buck-boost circuit needed to provide +11VSB (located in the black shrink wrap mid-cable).

The 8 pin power connector on the motherboard is identical to the ATX EPS power connector. However, the EPS power is on a right angle facing the top of the motherboard, you may have clearance issues installing the motherboard into some ATX chassis.


The CPU socket backplate has extrusions which will interfere with your chassis (assuming your chassis does not have a cut-out behind the CPU for accessing the backplate without removing the motherboard). These can be removed by fatiguing the metal (repeated bending using pliers) or with a dremel.

Some other minor modifications are required to convince the motherboard that it is running inside an HP chassis.

From HP service manual (PDF)

CPU fan (25): Connect pin 1 to pin 5

Front panel audio (2): Connect pin 2 (GND) to pin 4 (presence), since the pins are adjacent you can use a jumper. Connect pin 7 (sense_send) to pin 2 (GND).

Front panel IEEE1394 (1): Connect pin 11 (TPB-) to pin 12 (GND), since the pins are adjacent you can use a jumper.

Front panel LEDS (30): Connect pin 11 to Base and Collector of a 2222A NPN transistor, connect pin 12 to the 2222A Emitter.

From HP forum

Front panel USB3.0 (5): Connect pin 10 (USB3B_ID) to GND (one of pins 4, 7, 13, 16)

From HP forum

Front panel USB2.0 (4): Connect pin 8 (GND) to pin 10 (DRAIN), since the pins are adjacent you can use a jumper.


Top view of the front-panel headers on the Z420 motherboard with modifications
HP Z420 motherboard rear showing bridged connections for CPU fan, FP-USB3.0, FP-audio

A final word on power consumption: the Z420 motherboard consumes around 40W idle (E5-2630v2), but supports ACPI suspend-to-ram (S3) and consumes around 10W when in S3. Wake-on-LAN does not work when using an ATX power supply.

1 thought on “HP Z420 ATX modification

  1. Hal Martin Post author

    The Z210 motherboard also has the same power supply pinout as the Z420 18-pin PSU connector, and uses a P4 power connector for CPU power.

    The Z210 heat sink mounting holes are 100mm x 70mm (note: this is a non-standard size, you should probably use HP’s heat sink).
    Can’t img in a comment so here’s an annotated diagram: https://watchmysys.com/blog/wp-content/uploads/2022/06/HP_Z210_CMT.jpg

    Importantly, the Z210 motherboard never received a BIOS/ME firmware update to support Ivy Bridge. ONLY Sandy Bridge CPUs (E3-1200 v1) are supported. The system will not POST with an Ivy Bridge CPU.

    Reply

Leave a Reply to Hal Martin Cancel reply

Your email address will not be published.